M & G Dura-Vent DirectVent Pro 4'' ID with 6 5/8'' OD 90 degree Galvanized Swivel Elbow

M & G Dura-Vent DirectVent Pro 4'' ID with 6 5/8'' OD 90 degree Galvanized Swivel Elbow

Direct vent 90 degree Galvanized Swivel Elbow feature a fully unitized twist-lock construction. The swivel elbow allows the lock to remain fully engaged while aligning the elbow in the desired direction.M & G Dura-Vent DirectVent Pro 4'' ID with 6 5/8'' OD 90 degree Galvanized Swivel Elbow

Heat-Fab CCA16E45 Stainless Steel AL29-4C 16" Saf-T Vent CI+ 45- Elbow

Heat-Fab CCA16E45 Stainless Steel AL29-4C 16" Saf-T Vent CI+ 45- Elbow

Heat Fab CCA16E45 AL29 4C Stainless Steel Saf T Vent CIplus Vent Pipe Elbow 16" 45 ElbowOEM s have specified Saf T Vent for more than 15 years Saf T Vent was the first Venting System using AL 429C superferritic stainless steel to test and list to UL1738 S636 (Special Gas Vent Systems) The combination of high quality products and our engineering support system ensures your installation has high performance quality from adapter to termination CIplus Engineering gives the greatest flexibility to your system specs It s 1 inch airspace not only reduces required clearance to combustibles it also reduces vent skin temperature for safer maintenance conditions Reduced clearance to combustibles Strong mechanical joint locks in place Integral seal allows fast installation with no RTV Tested and listed to UL 1738 (Special Gas Vent) and ULC S636 (Type BH Gas Vent) in Canada Manufactured using AL429 4C Stainless Steel

Chimney Plus 300606 Protech 6''x 90 Degree Elbow AL29-4C

Chimney Plus 300606 Protech 6''x 90 Degree Elbow AL29-4C

• Manufactured to the Highest Quality Available.
• Design is stylish and innovative. Satisfaction Ensured.
• Great Gift Idea.

This 6in X 90 Degree AL29-4C VG FasNClamp Elbow has a flared end to accept the Ventinox liner at the top as well as a clamp to secure it. The bottom male end slips into a piece of pipe below and should be secured with four opposing pop rivets. Use our 0.3125in Nut Driver to tighten the clamp.

Simpson Duravent Pellet Stove Pipe, 24"

Simpson Duravent Pellet Stove Pipe, 24"

Features fully unitized twist-lock construction. In the USA it can be used in both vertical and horizontal installations. Inner wall is .012" type 430 stainless steel for pellet burning. Outer wall is .018" galvalume steel. Pipe OD is diameter plus 5/8". Listed 617J type L/Low temperature venting system. 1" minimum clearance to combustibles.

DuraVent W2-AA6 Stainless Steel AL29-4C 6 Inch FasNSealW2 Appliance Adapter From the FasNSeal Series

DuraVent W2-AA6 Stainless Steel AL29-4C 6 Inch FasNSealW2 Appliance Adapter From the FasNSeal Series

DuraVent W2 AA6 AL29 4C Stainless Steel FasNSeal Vent Pipe Adapter FasNSeal Collection 6 Inch FasNSealW2 Appliance AdapterWarranty Notice: MandG DuraVent warranty applies to this professional grade product only when installed by a trained professional installer This FasNSeal 6 Inch FasNSealW2 Appliance Adapter features a patented built in mechanical locking band and triple lipped directional gaskets which allows for ease of installation Adapts appliances to 6" Double Wall FasNSeal W2 Vent Pipe Features:Inner Diameter: 6"Fuel Types Compatible With: GasUL Listed: YesLength: 6"Double Wall ConstructionLimited Lifetime WarrantyAll FasNSeal single wall and double wall vent lengths and components feature patented built in mechanical locking band and triple lipped directional gaskets All pipes and components are engineered with smooth clean welds located 90 from mechanical locking bands This construction feature allows for ease of installation All FasNSeal components which come in contact with

Fireside Chimney Supply FireFlex 316Ti Basic Flexible Chimney Liner Kit - 3in x 20ft

Fireside Chimney Supply FireFlex 316Ti Basic Flexible Chimney Liner Kit - 3in x 20ft

• Your FireFlex Chimney Liner Kit will include a FireFlex 316Ti .006 thick stainless steel liner 13" x 13" top plate with rain cap and appliance connector for vertical connections.

Fireside Chimney Supply's FireFlex chimney lining systems are made of 316Ti stainless steel and are used for all fuels. Our FireFlex 316Ti stainless steel stainless steel chimney liner system is designed to reline existing chimneys or to be used in new construction.They are manufactured using the highest grade mill certified alloys. They are manufactured with a continuous strip of stainless steel, interlocked and diagonally crimped to produce a gas and water tight system of superior strength. With 7 ply seams and 10 corrugations between each seam it will deliver the flexibility needed to get the job done. Each FireFlex Kit includes our very own EZ connect system: Top plate or Flue fit top plate (optional) for the chimneys with the clay tile liner, both with EZ connect collars Rain Cap with screen to eliminate the pests Appliance connector with EZ connect for the insert or vertical hook-up Lifetime transferable chimney liner warranty Complete installation instructions UL1777 Listed in t

DuraVent 99365 Stainless Steel Class A 14" x 16" Class A Chimney Pipe Extended Roof Bracket

DuraVent 99365 Stainless Steel Class A 14" x 16" Class A Chimney Pipe Extended Roof Bracket

DuraVent 99365 Class A Stainless Steel DuraTech Vent Pipe Strap Bracket DuraTech Collection 14" x 16" Class A Chimney Pipe Extended Roof BracketWarranty Notice: MandG DuraVent warranty applies to this professional grade product only when installed by a trained professional installer The DuraTech 14" x 16" Class A Chimney Pipe Extended Roof Bracket is used to support the chimney when it extends more than 5 above the roof Provides stability to chimney against wind and snow Mounting brackets and adjustable tubing included Features:Inner Diameter: 14"Outer Diameter: 16"Bracket Length: 67" to 114"Supports Chimney when it Extends More Than 5" Above the RoofUL ListedDuraVent now offers DuraTech in large diameters to vent large scale residential fireplaces and building heating appliances DuraTech chimney is tested and listed for continuous operation at 1000 F flue gas temperatures one hour at 1400 F and ten minutes at 1700 F in accordance with the UL 103 test standard 10Â" 24Â" large diamete

Heat-Fab CCA26AJ Stainless Steel AL29-4C 26" Saf-T Vent CI+ 13"-20" Two Piece Adjustable Length

Heat-Fab CCA26AJ Stainless Steel AL29-4C 26" Saf-T Vent CI+ 13"-20" Two Piece Adjustable Length

Heat Fab CCA26AJ AL29 4C Stainless Steel Saf T Vent CIplus Vent Pipe Pipe Length 26" 13" 20" Two Piece Adjustable LengthOEM s have specified Saf T Vent for more than 15 years Saf T Vent was the first Venting System using AL 429C superferritic stainless steel to test and list to UL1738 S636 (Special Gas Vent Systems) The combination of high quality products and our engineering support system ensures your installation has high performance quality from adapter to termination CIplus Engineering gives the greatest flexibility to your system specs It s 1 inch airspace not only reduces required clearance to combustibles it also reduces vent skin temperature for safer maintenance conditions Reduced clearance to combustibles Strong mechanical joint locks in place Integral seal allows fast installation with no RTV Tested and listed to UL 1738 (Special Gas Vent) and ULC S636 (Type BH Gas Vent) in Canada Manufactured using AL429 4C Stainless Steel

3'' x 5'' DuraVent Type B Increaser - 3GVX5

3'' x 5'' DuraVent Type B Increaser - 3GVX5

M&G DuraVent 3GVX5 3" x 5" B-Vent Increaser

Fantech RSK 5 Backdraft Damper 5" Duct

Fantech RSK 5 Backdraft Damper 5" Duct

• Backdraft dampers with galvanized steel collar and lightweight aluminum damper blades
• Spring loaded for positive closure
• Duct Diameter : 5 inches

Fantech RSK 5 RSK Series Backdraft Damper

Heat-Fab 3808AR Stainless Steel 316 Rigid Liner 8" x 48" Stainless Steel Chimney Liner

Heat-Fab 3808AR Stainless Steel 316 Rigid Liner 8" x 48" Stainless Steel Chimney Liner

Heat Fab 3808AR Rigid Liner Stainless Steel 316 Saf T Liner Vent Pipe Pipe Length Ideal for relining chimneys that have deteriorated lining oversized lining or for lining chimneys with no existing lining Saf T Liner System adds years to the life of a chimney The product%27s resistance welded 24 gauge stainless steel fabrication meets code requirements and provides optimum safety As a substitute for 5 8" fireclay liner Saf T Liner cannot be beat Material Specifications:Saf T Liner systems consist of a Stainless Steel Liner Section (fabricated using either 304L or 316L stainless steel) insulated with Saf T Wrap chimney insulation Misc:Temperature Rating: 1000 Supported Fuels: Saf T Liner is suited for use with solid fuel and older oil or gas fired equipment that does not produce condensation in the vent Warranty: Lifetime Warranty UL Tested and Listed to UL 1777

Heat-Fab CCA06L24 Stainless Steel AL29-4C 6"x24" Saf-T Vent CI+ Straight Length

Heat-Fab CCA06L24 Stainless Steel AL29-4C 6"x24" Saf-T Vent CI+ Straight Length

Heat Fab CCA06L24 AL29 4C Stainless Steel Saf T Vent CIplus Vent Pipe Pipe Length 6"x24" Straight LengthOEM s have specified Saf T Vent for more than 15 years Saf T Vent was the first Venting System using AL 429C superferritic stainless steel to test and list to UL1738 S636 (Special Gas Vent Systems) The combination of high quality products and our engineering support system ensures your installation has high performance quality from adapter to termination CIplus Engineering gives the greatest flexibility to your system specs It s 1 inch airspace not only reduces required clearance to combustibles it also reduces vent skin temperature for safer maintenance conditions Reduced clearance to combustibles Strong mechanical joint locks in place Integral seal allows fast installation with no RTV Tested and listed to UL 1738 (Special Gas Vent) and ULC S636 (Type BH Gas Vent) in Canada Manufactured using AL429 4C Stainless Steel

DuraVent 6DFA-50 Aluminum DuraFlex AL DuraFlex AL Length - 6 Inch x 50 Foot From the DuraFlex AL Series

DuraVent 6DFA-50 Aluminum DuraFlex AL DuraFlex AL Length - 6 Inch x 50 Foot From the DuraFlex AL Series

DuraVent 6DFA 50 Flexible Liner Aluminum DuraFlex AL Vent Pipe Boxed Length DuraFlex AL Collection DuraFlex AL Length 6 Inch x 50 Foot This DuraFlex AL DuraFlex AL Length 6 Inch x 50 Foot is the ultimate in flexible components for strength and flexibility Use with Category I gas burning appliances with draft hood UL 1777 aluminum liner Flex lengths Features: Inner Diameter: 6" Fuel Types Compatible With: Gas Liquid Propane UL Listed: Yes Length: 600" Double Wall Construction Limited Lifetime Warranty An economical venting system used for relining masonry chimney for natural gas or liquid propane category I draft hood equipped appliances and appliances tested and listed to use Type B Gas Vent for a wide range of applications including: natural gas fireplaces gas fired furnaces boilers water heaters and wall or space heating applications Protects the masonry chimney from damaging effects of flue product condensation Looking for Simpson Dura Vent? You found it Simpson Dura Vent has change

Dundas Jafine BPC625 Flexible Insulated Ducting

Dundas Jafine BPC625 Flexible Insulated Ducting

• Dundas Jafine
• BPC625
• Heating & Air Products
• Black

Consists of a flexible helix core made of 2 ply polyester laminate and corrosion resistant zinc coated wire, surrounded by a blanket of glass fiber insulation, jacketed by a heavy duty, fire retardant black polyethylene vapor barrier. Can be installed in place of galvanized pipe in most applications. Due to its flexible nature, the need for elbows is eliminated, allowing for ease of installation in difficult to reach areas. It cuts easily with a knife and snips. The insulation blanket and vapor barrier jacket help reduce heat loss and condensation build up. Applications include: heating, air conditioning, exhausting, dryer venting, and fresh air intakes. Temperature range: 20 F. Velocity: 6000 F.P.M. C value: 23 min. UL and ULC approved as a Class 1 air duct. R4.2 insulation.

Heat-Fab 4810FLEX Stainless Steel 304 Rigid Liner 8" 30 Degree Crimped Elbow

Heat-Fab 4810FLEX Stainless Steel 304 Rigid Liner 8" 30 Degree Crimped Elbow

Heat Fab 4810FLEX Rigid Liner Stainless Steel 304 Saf T Liner Vent Pipe Elbow Ideal for relining chimneys that have deteriorated lining oversized lining or for lining chimneys with no existing lining Saf T Liner System adds years to the life of a chimney The product%27s resistance welded 24 gauge stainless steel fabrication meets code requirements and provides optimum safety As a substitute for 5 8" fireclay liner Saf T Liner cannot be beat Material Specifications:Saf T Liner systems consist of a Stainless Steel Liner Section (fabricated using either 304L or 316L stainless steel) insulated with Saf T Wrap chimney insulation Misc:Temperature Rating: 1000 Supported Fuels: Saf T Liner is suited for use with solid fuel and older oil or gas fired equipment that does not produce condensation in the vent Warranty: Lifetime Warranty UL Tested and Listed to UL 1777

Midwest Ducts Rectangular Duct Reducer - 6 Inches

Midwest Ducts Rectangular Duct Reducer - 6 Inches

• Ductwork reducer to maintain static pressure

Reduces the width of the ductwork to maintain static pressure.

4-327 4 in. Galv Chmny Cap (124-4)

4-327 4 in. Galv Chmny Cap (124-4)

• "GRAY METAL" 4" GALVANIZED SHANTY CAP
• Shanty Caps-Galvanized
• 4" size

GALVANIZED CHIMNEY CAP -

Fireside Chimney Supply FireFlex 316Ti Tee Flexible Chimney Liner Kit - 5in x 45ft

Fireside Chimney Supply FireFlex 316Ti Tee Flexible Chimney Liner Kit - 5in x 45ft

• Your FireFlex Chimney Liner Kit will include a FireFlex 316Ti .006 thick stainless steel liner 13" x 13" top plate with rain cap and Tee connector with 10" snout clean out cap for horizontal connections.

Fireside Chimney Supply's FireFlex chimney lining systems are made of 316Ti stainless steel and are used for all fuels. Our FireFlex 316Ti stainless steel stainless steel chimney liner system is designed to reline existing chimneys or to be used in new construction.They are manufactured using the highest grade mill certified alloys. They are manufactured with a continuous strip of stainless steel, interlocked and diagonally crimped to produce a gas and water tight system of superior strength. With 7 ply seams and 10 corrugations between each seam it will deliver the flexibility needed to get the job done. Each FireFlex Kit includes our very own EZ connect system: Top plate or Flue fit top plate (optional) for the chimneys with the clay tile liner, both with EZ connect collars Rain Cap with screen to eliminate the pests Appliance connector with EZ connect for the insert or vertical hook-up Lifetime transferable chimney liner warranty Complete installation instructions UL1777 Listed in t

6'' HeatFab Trim Collar - 2600B

6'' HeatFab Trim Collar - 2600B

Use Selkirk's trim collar for a 6" roof support to conceal the gap between the chimney pipe and the ceiling cut-out.Fabricated from 22-gauge cold roll steel. Up to 60% thicker than most hardware store brandsLaser and Advanced Resistance-welded seams makes snap together pipe obsolete. Guarantees a completely sealed seam: no smoke or flue leakageSaf-T Pipe offers a Full range of parts and sizes Beaded for furnace cementBlack high-temperature, low-luster finish painted with the highest quality silicone based stove paintIndividually wrapped and packaged. Readily available at Hearth Products specialty shops and from professional installers

Field Controls #b34tj08b Auto Draft Regulator

Field Controls #b34tj08b Auto Draft Regulator

• Field Controls #B34TJ08B Auto Draft Regulator
• FIELD CONTROLS
• Discovery CON, NBR, SUP, HWU

Blued Automatic Draft Regulator, Tee Joint, For 8" Pipe.

Z-Flex 2ZVB04 Z-V Adapt W/Back Flow Prev 4in

Z-Flex 2ZVB04 Z-V Adapt W/Back Flow Prev 4in

• Single Wall
• Diameter: 4
• Appliance Adapter

2ZVB04 Universal Appliance Adapter W/ Back Flow Preventer Universal Appliance Adapter Universal Appliance Adapter with Back Flow Preventer Z-Vent Special Gas Vent for Category Il, Il, IV Heating Equipment Is Designed for Use with Boilers, High Efficiency Furnaces, Pool Heaters, Unit Heaters and Tankless Water Heaters. Z-Vent is Manufactured Using AL29-4C, Advanced Ferritic Stainless Steel with Unmatched Corrosion Resistance, for Use with Condensing Furnaces and Boilers.

Heat-Fab 72420GC Stainless Steel AL29-4C 24" Saf-T Vent GC Horizontal In-Line 1/2" Drain

Heat-Fab 72420GC Stainless Steel AL29-4C 24" Saf-T Vent GC Horizontal In-Line 1/2" Drain

Heat Fab 72420GC AL29 4C Stainless Steel Saf T Vent GC Vent Pipe Drain 24" Horizontal In Line 1 2" DrainSaf T Vent GC is a single wall venting system fabricated from AL 29 4C stainless steel Designed for multiple applications Saf T Vent GC can be installed for use as Saf T Vent Special Gas Vent Saf T Vent Gas Vent Connector and Saf T Vent Masonry Chimney Liner Saf T Vent GC is fabricated from AL 29 4C stainless steel a corrosive resistant alloy high in both chromium and molybdenum The combination of AL 29 4C and smooth wall design makes Saf T Vent GC uniquely corrosion resistant and high temperature tolerant while giving it desirable flow characteristics not found in other venting systems or chimney lining systems `18 through 32 inch diameters Field applied silicone sealant required AL 29 4C Stainless Steel Patented Sure Seal closure system For use as Special Gas Vent Gas Vent Connector or Masonry Chimney Liner

Heat-Fab 4725SS Stainless Steel Rigid Liner 7" Saf-T Liner 316 13" x 13" 18g Top Plate

Heat-Fab 4725SS Stainless Steel Rigid Liner 7" Saf-T Liner 316 13" x 13" 18g Top Plate

Heat Fab 4725SS Rigid Liner Stainless Steel Saf T Liner 316 Vent Pipe Cap 7" Diameter 13" x 13" 18g Top PlateIn the last 20 years thousands of Saf T Liner systems have been installed Each system is built to last We offer a lifetime guarantee because we manufacture products that are simple to install and perform reliably year after year You can count on it The Saf T Liner system is designed to be so easy to install one professional on the job can do it alone Â- and have time to do another installation the same day Saf T Liner and Saf T Wrap are designed to make installation as trouble free as possible Easy to install Continuous seam welding Smooth inside with obstruction free joints Manufactured in a wide range of sizes 316L stainless steel

DuraVent 9406GACF Galvanized Class A Galvanized 36 Inch Chimney Pipe - GA (CF) with 6 Inch Inner Diameter

DuraVent 9406GACF Galvanized Class A Galvanized 36 Inch Chimney Pipe - GA (CF) with 6 Inch Inner Diameter

DuraVent 9406GACF Class A Galvanized DuraTech Vent Pipe Pipe Length 36 Inch Chimney Pipe Warranty Notice: MandG DuraVent warranty applies to this professional grade product only when installed by a trained professional installer Class A pipe is also known as Chimney Pipe orandnbsp;UL103 Pipe Class Aandnbsp;systems are used for high temperature exhaust gases from common solid fuels such as: Wood Coal Oil and other high output fuels This pipe is meant to be installed as a free standing chimney system and can be connected to your stove or appliance without the need for an existing chimney 5 8" DuraTech is a double wall all fuel chimney system for use with wood stoves fireplaces furnaces boilers ranges water heaters or other appliances fueled by wood oil coal or gas and zero clearance fireplaces that are factory built With a thermal Tech Blanket insulation encased between dual walls DuraTech offers the optimum in safety and performance It keeps the outer wall of the chimney cool while ensu

DuraVent 4TE-316 Stainless Steel Flexible Liner 4" Ventinox VFT Tee with Removable Snout

DuraVent 4TE-316 Stainless Steel Flexible Liner 4" Ventinox VFT Tee with Removable Snout

DuraVent 4TE 316 Flexible Liner Stainless Steel Ventinox Vent Pipe Tee Ventinox Collection 4" Ventinox VFT Tee with Removable SnoutWarranty Notice: MandG DuraVent warranty applies to this professional grade product only when installed by a trained professional installer Use as a 90 transition between liner and connector pipe at the wall thimble or rear flue outlet of a heater Removable Snout with internal draw band allows for easier through the wall thimble installation Ventinox components are made from either 316SS (VFT) or superferritic stainless steel (VG) Components feature an integral locking band avoiding the use of pop rivets Liners and components provide a penetration free top to bottom connection When venting solid fuel heaters Ventinox VFT must be insulated with either TherMix or ProFoil blankets to meet UL 1777 requirements For all other applications insulation is highly recommended for increased efficiency and draft performance Features:Inner Diameter: 4"Snout Length: 8"Mat